Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 31

Thread: Grinch still available?

  1. #21
    Join Date
    Nov 2012
    Posts
    9
    Post Thanks / Like

    Default Re: Grinch still available?

    Hello, I took some pictures on my Renard 32 Plus board. When I plug it in the RED power led turns on and the YELLOW status led comes on for about 2-3 seconds then turns off and starts the cycle again. The GREEN led does on turn on at all. When I try and plug in a SS board nothing happens. Any suggestions?

  2. #22
    Join Date
    Nov 2012
    Posts
    9
    Post Thanks / Like

    Default Re: Grinch still available?

    How do I upload a picture from my computer?

  3. #23
    Join Date
    Dec 2011
    Posts
    5,936
    Post Thanks / Like

    Default Re: Grinch still available?

    Quote Originally Posted by Ricki Baron View Post
    How do I upload a picture from my computer?
    google image host

  4. #24
    Join Date
    Oct 2014
    Location
    Sauk City, WI USA
    Posts
    1,111
    Post Thanks / Like

    Default Re: Grinch still available?

    Quote Originally Posted by Ricki Baron View Post
    How do I upload a picture from my computer?
    Reply
    Go Advanced (button bottom right)
    Find the insert Image.

  5. #25
    Join Date
    Jan 2017
    Posts
    303
    Post Thanks / Like

    Default Re: Grinch still available?

    Quote Originally Posted by Ricki Baron View Post
    Hello, I took some pictures on my Renard 32 Plus board. When I plug it in the RED power led turns on and the YELLOW status led comes on for about 2-3 seconds then turns off and starts the cycle again. The GREEN led does on turn on at all. When I try and plug in a SS board nothing happens. Any suggestions?
    This sounds like normal behavior for this controller. The flashing yellow light indicates the firmware is running, the green light flashes when it's receiving data. What do you have it connected to?

  6. #26
    Join Date
    Nov 2012
    Posts
    9
    Post Thanks / Like

    Default Re: Grinch still available?

    I am running Vixen 2.1 with a Renard Dimmer (modified) plug in. I have a Renard USB to RS485 Dongle. I have only hooked up one of my Renard Plus SSRhc 4 Channel High Current Relay Boards to it. I get no lights going at all from the relay board when I run one of my sequences.

  7. #27
    Join Date
    Oct 2014
    Location
    Sauk City, WI USA
    Posts
    1,111
    Post Thanks / Like

    Default Re: Grinch still available?

    with 2.1 make sure the com port ,speed, etc are set in the computer to match what you set in 2.1.

  8. #28
    Join Date
    Nov 2012
    Posts
    9
    Post Thanks / Like

    Default Re: Grinch still available?

    I have checked all this already but still nothing. Thanks for the suggestion.

  9. #29
    Join Date
    Jan 2017
    Posts
    303
    Post Thanks / Like

    Default Re: Grinch still available?

    If you're trying to trouble-shoot the controller you might try this utility, Renard Tester. If you can't get output with it, try increasing the number of channels. Your controller might be programmed to start at a higher channel count. A photo of the board w/jumpers visible would also help. When sending data, you should at least get a flashing indicator. Dean (aka Falcon) over at the other site is great about helping with his controllers. I have a couple of RP32's and they've been solid performers.

  10. #30
    Join Date
    Oct 2014
    Location
    Sauk City, WI USA
    Posts
    1,111
    Post Thanks / Like

    Default Re: Grinch still available?

    Ricki,
    Where are you located? Maybe you can make a "local" contact to help out.

Page 3 of 4 FirstFirst 1234 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •