Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Blog Blogs
  • angus40's Avatar
    Today, 08:08 PM
    Here it is with the esp-Wemos D1 directly connected . I used 34Vdc to the board and 5v to the esp . No resistors etc. Stable Red
    294 replies | 42856 view(s)
  • angus40's Avatar
    Today, 08:00 PM
    I used a digital variable buck with the 100w Robg . The series resistor is to smooth the signal from noise or rogue waves from what I have read .
    294 replies | 42856 view(s)
  • jklingert's Avatar
    Today, 07:31 PM
    Is the 330 ohm resistor in series or tied to ground? What is the purpose of the resistor? The power supply is a meanwell 36v turned all the way...
    294 replies | 42856 view(s)
  • Zeph's Avatar
    Today, 07:01 PM
    Sigh. OK, there's no good way to say this so I'll just blurt it out: I connected reversed 5V power to an ESPixelStick (connected to 200 5V WS811...
    546 replies | 97405 view(s)
  • angus40's Avatar
    Today, 07:00 PM
    A few things to try is 1) reduce the intensity to see if flicker stops 2) add a 330 ohm resistor to the data line 3) reduce the 30v until you reach...
    294 replies | 42856 view(s)
  • jklingert's Avatar
    Today, 06:28 PM
    Yes, the 5v pixels plugged into the controller by themselves work fine. When I plug the same pixels into the output of the floods they flicker just...
    294 replies | 42856 view(s)
  • Cdanna77's Avatar
    Today, 05:44 PM
    Cdanna77 replied to a thread Pixel to pvc in PVC
    Oh I just seen what you posted. Sorry.
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 05:42 PM
    wilmar replied to a thread Pixel to pvc in PVC
    Fyi I used petg with 100 percent infill Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • Cdanna77's Avatar
    Today, 05:40 PM
    Cdanna77 replied to a thread Pixel to pvc in PVC
    Thank you put it up on Thingiverse. Awesome little clip. Do you think would hold up better to hot and cold PETG or ABS. Iím in NYC so our Xmas...
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 03:46 PM
    wilmar replied to a thread Pixel to pvc in PVC
    https://www.thingiverse.com/thing:4541302 Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 03:22 PM
    wilmar replied to a thread Pixel to pvc in PVC
    Ok super easy print Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • Cdanna77's Avatar
    Today, 03:20 PM
    Cdanna77 replied to a thread Pixel to pvc in PVC
    I would be interested in the kung fu clip .stl my self.
    23 replies | 559 view(s)
  • Byhova's Avatar
    Today, 03:14 PM
    Byhova replied to a thread Pixel to pvc in PVC
    Could you upload that Kung Fu grip clips because that might work for my pixelbulbs as it could replace the zipties that are on each side of my wires...
    23 replies | 559 view(s)
  • angus40's Avatar
    Today, 02:58 PM
    Have you tested your pixelsticks with regular pixels ?
    294 replies | 42856 view(s)
  • wilmar's Avatar
    Today, 02:31 PM
    wilmar replied to a thread Pixel to pvc in PVC
    I did come up with a clip that comes with Kung fu grip , and so far worked on every string I have . Regular C9 , bullets,and square . And by Kung...
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 02:24 PM
    wilmar replied to a thread Pixel to pvc in PVC
    Ok picture wasnít showing when I responded so I thought of something else ... yes you are right I like that idea not sure how it will print have to...
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 10:13 AM
    wilmar replied to a thread Pixel to pvc in PVC
    Would definitely be easier if I had one but Iíll draw up a pic showing what measurements I need and send . Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • Byhova's Avatar
    Today, 10:09 AM
    Byhova replied to a thread Pixel to pvc in PVC
    I could possibly get you the specs if you tell me what you need or I could even send you one from a cut strand if that would make it easier. I...
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 10:09 AM
    wilmar replied to a thread Pixel to pvc in PVC
    Yea I made those but thought if clipped to the base it would be easier to line up the bulbs with only one pivot point vs 2 . But can do either way ...
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 10:06 AM
    wilmar replied to a thread Pixel to pvc in PVC
    No I dont have any but if someone could get me all the measurements that may get me closer Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • Byhova's Avatar
    Today, 09:36 AM
    Byhova replied to a thread Pixel to pvc in PVC
    I have DIYLEDExpress pixelbulbs for my house outline. I just finished zip tying them to PVC. I now have just over 2k pixelbulbs ziptied to pvc. I...
    23 replies | 559 view(s)
  • mrGrumpy's Avatar
    Today, 09:28 AM
    mrGrumpy replied to a thread Pixel to pvc in PVC
    Thinking the Pixabulb clip would be more universal if the wire could be the holding point. One on left and right. Not an artist, but here is a...
    23 replies | 559 view(s)
  • jklingert's Avatar
    Today, 08:43 AM
    I am having a problem with some of the 50W units i purchased preassembled from RobG's tindie shop...
    294 replies | 42856 view(s)
  • wilmar's Avatar
    Today, 06:46 AM
    wilmar replied to a thread Pixel to pvc in PVC
    #2 Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • wilmar's Avatar
    Today, 06:35 AM
    wilmar replied to a thread Pixel to pvc in PVC
    First prototype lol I need to raise the holder a bit to allow more room for the wires but looks doable. Sent from my iPhone using Tapatalk
    23 replies | 559 view(s)
  • Macrosill's Avatar
    Today, 06:18 AM
    Happy 70th Birthday bitelf ! Hope you have a wonderful day, and very best wishes from everyone here at Do It Yourself Christmas.
    0 replies | 29 view(s)
  • pmiller's Avatar
    Today, 12:13 AM
    You will notice on the webpage of the controller that you assign the output for 50 pixels and it will show a start universe of 1 and start channel 1....
    5 replies | 132 view(s)
  • pmiller's Avatar
    Today, 12:09 AM
    In the configuration setup it shouldn't be 50 but 150. Each pixel requires 3 channels. On the controller you should have 150 outputs. Make sure...
    5 replies | 132 view(s)
  • mrGrumpy's Avatar
    Yesterday, 11:45 PM
    mrGrumpy replied to a thread Pixel to pvc in PVC
    If Rayís Pixelbulbs are like DIYLEDEXPRESSís, than they have a slight concave shape on the base, therefore glue may not be as strong as expected with...
    23 replies | 559 view(s)
  • Wildbill's Avatar
    Yesterday, 11:32 PM
    Sorry no I use Xlights Sent from my iPhone using Tapatalk
    5 replies | 132 view(s)
More Activity